燃?xì)獍l(fā)電機組可以手動操作，合上預供油開關，啟動電動預供油泵（或扳動手搖機油泵）。待主油道壓力達到100kPa后，按下起動按鈕，機組起動后，立即釋放起動按鈕并斷開起動開關。機組每次起動時間為5s，若連續起動三次不成功，應檢查原因，排除故障后再起動。發動機運行后，可按下“翻頁”按鈕，通過液晶顯示屏檢查發動機運行中各項技術參數的變化。起動成功后應怠速暖機，當機油溫、水溫達到40℃以上，方可加速、加載。
The gas generator set can be manually operated by closing the pre oil supply switch and starting the electric pre oil pump (or pulling the hand operated oil pump). After the main oil duct pressure reaches 100kPa, press the start button. After the unit starts, immediately release the start button and disconnect the start switch. The starting time of the unit is 5 seconds each time. If the unit fails to start three consecutive times, the cause should be checked and the fault should be eliminated before starting. After the engine is running, you can press the "page turning" button to check the changes in various technical parameters during engine operation through the LCD display screen. After successful starting, the engine should be warmed up at idle speed. Only when the oil and water temperature of the engine reach 40 ℃ or above can acceleration and loading be carried out.
按動或調節控制屏上加減速旋鈕調整機組的頻率，使之略高于額定頻率。調整控制屏上的電壓調節器的微調旋鈕，使交流電壓表在400V位置，合上主開關，機組便向負載供電。機組帶載運行后，若電壓、頻率偏離了額定值，分別調節轉速旋鈕和電壓整定電位器，使電壓頻率達到額定值。

Press or adjust the acceleration/deceleration knob on the control screen to adjust the frequency of the unit to slightly higher than the rated frequency. Adjust the fine adjustment knob of the voltage regulator on the control panel to make the AC voltmeter at 400V, close the main switch, and the unit will supply power to the load. After the unit operates with load, if the voltage and frequency deviate from the rated value, adjust the speed knob and voltage setting potentiometer respectively to make the voltage and frequency reach the rated value.
燃?xì)獍l(fā)電機組還可以自動操作，對于應急自動燃?xì)獍l(fā)電機組來說，發電機組應該一直處于準啟動狀態（定期自動預潤滑、保持油溫水溫），在接到自動控制系統的啟動命令后（失去市電、總體功率不足等），機組會自動啟動，并且在達到額定狀態后自動合閘帶載。
The gas generator set can also operate automatically. For emergency automatic gas generator sets, the generator set should always be in a quasi start state (regular automatic pre lubrication, maintaining oil temperature and water temperature). After receiving a start command from the automatic control system (loss of mains power, overall power shortage, etc.), the unit will automatically start and automatically close and load after reaching the rated state.
燃?xì)獍l(fā)電機組的停機和啟動一樣可以在機旁、控制屏處操作。發動機的停機操作一般在主開關已經分閘后進行。無論在機旁、監控室還是自動進行操作，基本的過程都是一樣的。正常停機應逐步卸去負載并主開關分閘后，將轉速選擇開關置“怠速”位，天然氣發動機機轉速至1500r/min。按照天然氣發動機使用維護說明書的要求對機組進行冷機后，將“停機”旋鈕旋至停機位置，使發動機停止工作。停機后將電氣開關全部置停機位置上，各調節旋鈕亦復原到停機的相應位置，以便下次起動。
The shutdown and startup of gas generator units can be operated from the machine side and control panel. The shutdown operation of the engine is usually carried out after the main switch has been opened. The basic process is the same whether operating on the machine, in the monitoring room, or automatically. After gradually unloading the load and opening the main switch during normal shutdown, set the speed selection switch to the "idle" position and raise the natural gas engine speed to 1500r/min. After cooling the unit according to the requirements of the natural gas engine maintenance manual, turn the "stop" knob to the stop position to stop the engine from working. After stopping the machine, place all electrical switches in the stop position, and restore each adjustment knob to the corresponding stop position for the next start.
本文由工業尾氣發電機組友情奉獻.更多有關的知識請擊:http://087801.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is a friendly contribution from industrial exhaust gas generator sets. For more relevant knowledge, please click on: http://087801.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned